Layer height, infill and material: what your print settings actually change
What layer height, infill and PLA, ABS or PETG change in a 3D printed part, shown in animated diagrams, and how to choose settings for yours.
Print the same model twice with different settings and you can get two very different parts: one smooth and light, the other rougher but tougher. Three choices make the difference, and you make all three when you ask us for a quote.
This guide shows what each one actually does. The models on this page are live: drag them to turn them, move the sliders, and watch the part change.
In 30 seconds
- Layer height sets how smooth curves and slopes look. Thinner layers look smoother, but there are more of them to print.
- Infill is the structure inside. It changes weight, material use and, usually, strength, never the outside.
- Material decides how the part behaves: PLA for crisp detail, ABS for warmer places, PETG for toughness and moisture.
- Not sure? PLA, 0.20 mm Standard and 15% infill suit most parts, and we review every request before confirming the price.
How a 3D printer builds a part
We print with FDM, short for fused deposition modelling. A heated nozzle melts a plastic filament and lays it down as a thin bead, tracing the outline and the inside of one flat layer, then traces the next layer on top of it. A part is hundreds of these layers stacked together.
Before anything is printed, software called a slicer cuts your 3D model into those horizontal layers and plans the nozzle’s path through each one. Step through it below. Every setting in this guide is an instruction to the slicer: how thick to make each layer, how much of the inside to fill, and which plastic to melt.
A part is hundreds of flat layers. Every setting changes how those layers are made.
Layer height: how smooth the surface looks
Every layer is flat. A vertical wall is simply the same outline repeated, so it looks the same at any layer height. A curve or a slope is different: each layer steps in a little from the one below, and the surface becomes a small staircase. This is called stair-stepping, and the thinner the layers, the smaller the steps.
Choose a layer height below and the dome is printed again with it. The cyan lines are the surface as designed; the layers are what the printer can make of it. Look at the top, where the surface is shallowest: that is where the steps show.
150 layers in this 30 mm part20% more than Draft
Cyan lines: the surface as designed. Layers drawn 4× thicker.
3D model: a dome printed in 0.20 mm layers. Each layer is a flat step, so the curved top becomes a staircase; thinner layers make smaller steps that follow the designed surface more closely.
The quotation page offers three layer heights:
Thinner layers have a cost: a 30 mm-tall part is 125 layers at 0.24 mm but 188 at 0.16 mm, about half as many again, and each one has to be printed. That is why the estimated price on the quotation page changes with the layer height you pick.
Infill: what is inside the part
Most 3D printed parts are not solid. The nozzle prints a few unbroken outlines called walls, plus solid top and bottom layers, so the outside is closed and smooth. Inside, it prints a lighter lattice called infill. The infill percentage is how much of that inside space is filled with plastic.
Below, the top layers of a part have been lifted off so you can see inside. Move the slider and the grid is printed again; tick “Show the top layers” and the part looks exactly the same at any setting.
Same range as the quotation page; 15% is our default.
About 15% filledwalls and top unchanged
What changes when you raise infill
- The part gets heavier and uses more plastic.
- It takes longer to print, because the nozzle has more to trace.
- It usually gets stronger and stiffer, especially against crushing and around screws.
- The outside looks the same.
You can choose any infill from 5% to 100% in 5% steps. 15% is our default and suits most models, prototypes and display pieces. Raise it for parts that carry load, get clamped or take screws, and say what the part does in Special mentions so we can check your choice when we review the request. On the quotation page, infill does not change the model’s measured volume, which comes from its geometry, but it can change the estimated price.
Material: how the part behaves
Layer height and infill shape the part. The material decides how it behaves once it is in use: how it handles heat, knocks and moisture. We print in three plastics:
| Material | Strengths | Good for | Keep in mind |
|---|---|---|---|
| PLA | Stiff, crisp detail, clean finish | Models, prototypes, display pieces, indoor parts | Softens with heat, so not for hot cars or direct sun |
| ABS | Tough, handles higher temperatures than PLA | Functional parts, enclosures, parts that get warm | A more technical material to print |
| PETG | Tough, slightly flexible, resists moisture | Mechanical and outdoor parts, parts near moisture | Surface finish can be less crisp than PLA |
PLA is the default on the quotation page and the right choice for most models. Move to PETG when the part has to take knocks or live near water, and to ABS when it will get warm. Colours are white, black, blue and yellow, and you can compare them on a 3D part in the materials section of our home page.
Three starting points
Most parts fall into one of these. Use them as a first choice, then adjust on the quotation page.
Questions
Which settings should I choose if I am not sure?
Start with the defaults on the quotation page: PLA, 0.20 mm Standard layers and 15% infill. They suit most parts. Tell us in Special mentions what the part is for, and we review your model and settings before confirming the price on WhatsApp.
Does infill change how my part looks?
No. Infill is the structure inside the part. The walls that form the outside are the same at every infill setting, so the part looks the same from the outside.
Will I see the difference between layer heights?
On flat tops and straight vertical walls you will barely see a difference. It shows on curves, slopes, domes and small raised details, where thinner layers leave smaller steps.
Which 3D file formats can I upload?
STL, OBJ, 3MF or STEP. Upload it on the quotation page, see it in 3D, choose your settings and send the request. Asking for a quote is free.
Ready to make it?
Upload your model for a free quote, shop a ready-made design, or ask us to design the part. We confirm every price with you on WhatsApp.

